How to scaffold your own rails with parts from a DIY car parts kit

From a simple bolt on to a multi-layered scaffold of rails, this video tutorial from the creators of Scaffolding Parts from the Garage shows how to build your own rail harnesses from parts.

This DIY car harnesses include a simple two piece piece design, with a threaded section to hold the front wheel.

It’s designed to be used in a car without a wheel drive system, so you can get around without one, too.

The part is made of PVC pipe, and the pipe has a plastic backing so it can be easily bent.

This means that the car harness can be used with a car wheel, as well as a car seat or wheel-base car seat.

To build your rails, use PVC pipe as shown, then cut it in half lengthwise, and then weld it to the front of the car.

This is a simple example of the rails you can build using PVC pipe.

It will be easier to make it if you have a few small holes cut out of the PVC pipe so you don’t have to worry about splitting the PVC.

The parts you need to make this DIY car wheel harness:A plastic frame for the front axle.

A plastic pipe to hold your front axle in place.

A 2-piece plastic wheel with a locking nut on one side.

Step 1: Cut the PVC Pipe.

Step 2: Make the PartsThe PVC pipe is made from a PVC pipe cut into strips.

It can be made in a wide variety of shapes, depending on the PVC you want to use, and its width and length can vary depending on how much of the pipe you want.

This part of the DIY car part kit is made out of PVC and PVC pipe and PVC glue.

You can buy PVC pipe from your local hardware store, or you can make your own from scrap PVC pipe with a plastic knife.

Once you have the PVC in your pipe, you’ll need to drill holes for the axle, wheels and front axle, which are all drilled out of one piece of PVC.

This will be where the wheel is attached.

Step 3: Drill Out the Wheel and Rear Axle.

Step 4: Cut a Hole in the WheelFor this part, you can use any 3/8-inch drill bit.

You could use a 2.5-inch bit if you’re a bit more careful.

You should also use a 1/4-inch (3mm) drill bit for this part.

Step 5: Make a Hole on the Wheel.

Step 6: Drill the Hole on Your Wheel.

Once the wheel has been drilled, the holes you drilled will need to be drilled to make a hole in the wheel.

You’ll need a 4-inch hole, a 3-inch one and a 1-inch and 1-mm one.

You also need a piece of plywood to secure the wheel to the frame.

To drill out the wheel holes, simply drill one in the middle of the wheel, and cut it out to make the hole.

Step 7: Make One Hole in Your Front Wheel.

To make the front and rear axle, you simply cut a hole for them, and drill them out of a piece.

The holes are a bit longer than you want, so make sure you’re drilling through all four holes.

The front and the rear wheels are drilled with a 3/16-inch hex driver, which is used to drill out holes in PVC pipe in a standard 3/4″ bit.

Step 8: Drill The Hole in The Rear Wheel.

If you’re using a 3.5mm bit, make sure the hole is drilled just as you drilled the front wheels, and use the 3/32-inch driver to drill a 1.5″ hole for the rear wheel.

Step 9: Drill a 1″ Hole in One Hole for Your Rear WheelWith the rear axle drilled, you’re ready to attach the wheel and the front to the car, which you can then drive around in.

Step 10: Make Your Own Car WheelThis is the DIY wheel harness that the creators built with PVC pipe on the back.

They took the wheels off of a Ford Fiesta GT and used PVC pipe to make all the front/rear wheels.

The front wheel is an 18-inch wheel and it’s covered in the PVC to make sure it won’t split during transport.

It also has a locking ring that you can attach to the rear of the vehicle to keep it secured in place while you’re driving.